Commit aee51faf authored by schneider's avatar schneider
Browse files

feat(bmetest): Show values on the screen

parent 77aee1a9
......@@ -67,8 +67,6 @@ CMSIS_ROOT=$(LIBS_DIR)/CMSIS
# Source files for this test (add path to VPATH below)
SRCS = main.c
SRCS += oled96.c
SRCS += fonts.c
SRCS += pmic.c
SRCS += bosch.c
SRCS += bhy_support.c bhy_uc_driver.c bhy.c
......@@ -79,6 +77,7 @@ SRCS += LCD_Driver.c
SRCS += GUI_Paint.c
SRCS += DEV_Config.c
SRCS += font24.c
SRCS += font16.c
SRCS += font24CN.c
SRCS += card10.c
SRCS += display.c
......
......@@ -9,9 +9,10 @@
#include "tmr_utils.h"
#include "i2c.h"
#include "gpio.h"
#include "oled96.h"
#include "bme680.h"
#include "bosch.h"
#include "GUI_DEV/GUI_Paint.h"
#include "Fonts/fonts.h"
#include "card10.h"
......@@ -26,12 +27,6 @@ int main(void)
card10_init();
card10_diag();
oledInit(0x3c, 0, 0);
oledFill(0x00);
oledWriteString(0, 0, "Hello", 0);
oledWriteString(0, 2, "my name is", 0);
oledWriteString(0, 4, "card10", 1);
struct bme680_dev gas_sensor;
gas_sensor.dev_id = BME680_I2C_ADDR_PRIMARY;
gas_sensor.intf = BME680_I2C_INTF;
......@@ -87,11 +82,26 @@ int main(void)
printf("T: %.2f degC, P: %.2f hPa, H %.2f %%rH ", data.temperature / 100.0l,
data.pressure / 100.0l, data.humidity / 1000.0l );
char buf[128];
sprintf(buf, "T: %.2f degC", data.temperature / 100.0l);
Paint_DrawString_EN(0, 0, buf, &Font16, 0x0000, 0xffff);
sprintf(buf, "P: %.2f hPa", data.pressure / 100.0l);
Paint_DrawString_EN(0, 16, buf, &Font16, 0x0000, 0xffff);
sprintf(buf, "H: %.2f %%rH", data.humidity / 1000.0l);
Paint_DrawString_EN(0, 32, buf, &Font16, 0x0000, 0xffff);
//printf("%.2f,%.2f,%.2f\n", data.temperature / 100.0f,
// data.pressure / 100.0f, data.humidity / 1000.0f );
/* Avoid using measurements from an unstable heating setup */
if(data.status & BME680_GASM_VALID_MSK)
if(data.status & BME680_GASM_VALID_MSK) {
printf(", G: %d ohms", data.gas_resistance);
sprintf(buf, "G: %d ohms", data.gas_resistance);
Paint_DrawString_EN(0, 48, buf, &Font16, 0x0000, 0xffff);
}
LCD_Update();
printf("\n");
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment