Commit bc6e2b0d authored by schneider's avatar schneider
Browse files

feat(helloworld): Setup pmic

parent 97114129
......@@ -69,7 +69,7 @@ SRCS = main.c
SRCS += ../lib/card10/oled96.c
SRCS += ../lib/card10/fonts.c
SRCS += bhy_support.c bhy_uc_driver.c bhy.c
SRCS += MAX77650-Arduino-Library.c
# Where to find source files for this test
VPATH = .
......@@ -83,6 +83,9 @@ IPATH += ../lib/bosch/BHy1_driver_and_MCU_solution/driver/inc
IPATH += ../lib/bosch/BHy1_driver_and_MCU_solution/examples/firmware/
VPATH += ../lib/bosch/BHy1_driver_and_MCU_solution/driver/src
IPATH += ../lib/maxim/MAX77650-Arduino-Library
VPATH += ../lib/maxim/MAX77650-Arduino-Library
# Enable assertion checking for development
PROJ_CFLAGS+=-DMXC_ASSERT_ENABLE
......
......@@ -55,6 +55,7 @@
#include "bhy.h"
#include "Bosch_PCB_7183_di03_BMI160_BMM150-7183_di03.2.1.11696_170103.h"
#include "bhy_uc_driver.h"
#include "MAX77650-Arduino-Library.h"
/***** Definitions *****/
......@@ -95,6 +96,70 @@ uint32_t ecg_read_reg(uint8_t reg)
return (rx_data[1] << 16) | (rx_data[2] << 8) | rx_data[3];
}
void pmic_init(void)
{
uint8_t didm = MAX77650_getDIDM();
uint8_t cid = MAX77650_getChipID();
printf("MAX7765x DIDM: 0x%02x CID: 0x%02x\n", didm, cid);
MAX77650_setIP_SBB0(0b11); //Limit output of SBB0 to 500mA
MAX77650_setTV_SBB0(0b101000); //Set output Voltage of SBB0 to 1.8V
MAX77650_setADE_SBB0(0b0); //Disable Active Discharge at SBB0 Output
MAX77650_setEN_SBB0(0b110); //Enable SBB0 is on irrespective of FPS whenever the on/off controller is in its "On via Software" or "On via On/Off Controller" states
MAX77650_setIP_SBB1(0b11); //Limit output of SBB1 to 500mA
MAX77650_setTV_SBB1(0b100000); //Set output Voltage of SBB1 to 1.2V
//MAX77650_setTV_SBB1(0b100010); //Set output Voltage of SBB1 to 3.3V
MAX77650_setADE_SBB1(0b0); //Disable Active Discharge at SBB1 Output
MAX77650_setEN_SBB1(0b110); //Enable SBB1 is on irrespective of FPS whenever the on/off controller is in its "On via Software" or "On via On/Off Controller" states
MAX77650_setIP_SBB2(0b11); //Limit output of SBB2 to 500mA
MAX77650_setTV_SBB2(0b110010); //Set output Voltage of SBB2 to 3.3V
//MAX77650_setTV_SBB2(0b110100); //Set output Voltage of SBB2 to 5.0V
MAX77650_setADE_SBB2(0b0); //Disable Active Discharge at SBB2 Output
MAX77650_setEN_SBB2(0b110); //Enable SBB2 is on irrespective of FPS whenever the on/off controller is in its "On via Software" or "On via On/Off Controller" states
// Prepare the PMIC LEDs
MAX77650_setLED_FS0(0b01);
MAX77650_setINV_LED0(false); //LED red: phase operation
MAX77650_setBRT_LED0(0b00000); //LED red: brightness
MAX77650_setP_LED0(0b1111); //LED red: LED period
MAX77650_setD_LED0(0b1111); //LED red: LED duty-cycle
MAX77650_setLED_FS1(0b01);
MAX77650_setINV_LED1(false); //LED green: phase operation
MAX77650_setBRT_LED1(0b00000); //LED green: brightness
MAX77650_setP_LED1(0b1111); //LED green: LED period
MAX77650_setD_LED1(0b1111); //LED green: LED duty-cycle
MAX77650_setLED_FS2(0b01);
MAX77650_setINV_LED2(false); //LED blue: phase operation
MAX77650_setBRT_LED2(0b00000); //LED blue: brightness
MAX77650_setP_LED2(0b1111); //LED blue: LED period
MAX77650_setD_LED2(0b1111); //LED blue: LED duty-cycle
MAX77650_setEN_LED_MSTR(true); //LEDs Master enable
}
void set_led(uint8_t led, uint8_t val)
{
if(led == 0) {
MAX77650_setLED_FS0(val > 0 ? 0b01 : 0);
MAX77650_setBRT_LED0(val);
}
if(led == 1) {
MAX77650_setLED_FS1(val > 0 ? 0b01 : 0);
MAX77650_setBRT_LED1(val);
}
if(led == 2) {
MAX77650_setLED_FS2(val > 0 ? 0b01 : 0);
MAX77650_setBRT_LED2(val);
}
}
// *****************************************************************************
int main(void)
{
......@@ -160,11 +225,24 @@ int main(void)
printf("%02x: 0x%06x\n", i, val);
}
pmic_init();
while (1) {
LED_On(0);
set_led(0, 33);
set_led(1, 0);
set_led(2, 0);
TMR_Delay(MXC_TMR0, MSEC(500), 0);
LED_Off(0);
set_led(0, 0);
set_led(1, 33);
set_led(2, 0);
TMR_Delay(MXC_TMR0, MSEC(500), 0);
set_led(0, 0);
set_led(1, 0);
set_led(2, 33);
TMR_Delay(MXC_TMR0, MSEC(500), 0);
printf("count = %d\n", count++);
}
}
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment